Just click on a tab to see the most frequently asked questions for that category.

What information do I need to provide to get a quote?

TAMPI -> Temperature, Application, Medium (flow), Pressure, Inside Diameter
What is the useful shelf life of Petersen Inflatable Items / how long can the plug be in place? Petersen PeteStop™ and Multi-Flex® Plugs and Inflatables are made from synthetic materials generally with a shelf life many more years longer than molded rubber plugs. We do not test the final product for length of life but have anecdotal feedback they have been used for years before returning for repair, testing, and recertification. Every project is different so only length of life generalizations are possible. Please contact Petersen Engineering for details.
What orientations can I install my plug? It can be installed horizontally or vertically and into a horizontal or vertical run of pipe It can be installed into unique circumstances such as ROV, tunnel, or rock

What are my options for a plug to be placed into service?

- It can be inflated from the end or from the side - It can be lowered into place with a crane or hoist It can be rolled in on wheels or other device It can be inserted through a hot tap - It can be inserted through a hole smaller than the pipe size It can be installed via ROV - Other placement options are available

Water vs Air or Nitrogen Inflation.

Water is not compressible so is less dangerous than inflation with air or another gas. Water is especially preferred for large plugs and high pressure but it is still a judgement based on what is in the pipeline and the consequence of a plug failure for any reason.

Can the plug be fit through a smaller than pipe diameter opening

- Yes. We have many options available from hot tap insertions to multi-segmented mechanicals. - We test plugs only for rated size pipeline but understand they are sometimes used in a smaller diameter pipe. As the size is reduced there will be more wrinkles in the outer ply so general more seepage past the plug. This may or may not provide an acceptable block.

Can the plug be fit through elbows and other tight bends?

Yes. We have many application specific options available. Our very flexible Multi-FlexTM plugs excel in this application.

Are the plugs chemical, temperature, and puncture resistant?

- The hydrocarbon resistant Multi-Flex® plugs have a 200°F maximum service temperature and may be modified for up to 400°F. - Multi-Flex® Plugs may be customized for most chemical resistance requirements. Multi-Flex® plugs have a much higher puncture and tear resistance than rubber molded Plugs and may be customized with Kevlar for even greater puncture resistance. - None of our inflatable plugs can withstand 600F and weld splatter can damage them. - The temperature of the pipe can sometimes be reduced by flooding the plug area with water. - The splatter can be reduced somewhat by the welding technique, we can add a Kevlar outer ply, or the plug moved further from the weld area.

Will a Kevlar Viton plug resist Hydrogen Sulfide and Hydrofluoric Acid

Based on our best information the Kevlar Viton B material used in manufacturing the 114-0245-KV plug provides resistance to Hydrofluoric acid. It is still recommended that any product be tested under actual environment as conditions may vary considerably and we do not have the facility to perform chemical tests.

How do we deflate the plug inflated with (Air or Inert Gas)?

NOTE: DO NOT pull on the Inflation hose to remove the Inflatable Plug - Disconnect the air source and open any valve on the Inflatable Plug. - Petersen recommends using a Vacuum Generator to deflate larger Inflatable Plugs. - Water Deflation - Disconnect the water source from the Inflatable Plug. - Connect the hose to the water outlet. - Verify that the water outlet hose drains into a tank or area that can collect the drained water. - Monitor and track the output as needed. Removing the Plug - Carefully remove the Inflatable Plug only after it is completely deflated.

Is it safe to use the plug with workers down stream?

Safety is our top priority. All pipe plugs must be blocked or anchored adequately against a force equal to the head pressure times the cross-sectional area of the pipe. Debris or protrusions in the pipeline can damage a seal or rupture inflatable plugs. NEVER use an inflatable plug when its failure could cause injury or catastrophic damage or as the only means of protection for personnel working downstream. NEVER use a test pressure greater than the capacity of the weakest pipe or component in the system. Actual conditions vary so user must accept full risk and responsibility for the selection and use of any product.

What determines the rated head and inflation pressure?

The maximum pipeline head pressure is generally 50% of the plug maximum inflation pressure. It can vary based on actual pipeline conditions and the product being blocked. The head pressure is considered the maximum differential pressure up and down stream of the plug. If the pressure is 100 psi up stream and 50 psi downstream of the plug, the head pressure is 50 psi. With a 120”WC vacuum (4.33 psi) on one side of the plug and no vacuum or pressure on the opposite side of the plug, the head pressure is 4.33 psi.

What are typical applications for a Multi-Flex® plug?

The plug is used where there is a small opening for inserting a plug and/or when greater pressure, chemical, and temperature characteristics are desired.

Can the Multi-Flex® plugs be used for pressure testing?

Our Multi-Flex plugs such as the 113 to 127 series plugs have the highest minimum to maximum size ratio in the industry but the fabric reinforced outer ply develops wrinkles as the pipe diameter reduces thus allowing more seepage past the plug. They can be customized for testing a specific size but a mechanical or rubber plug if more typical for testing.

Will your plug provide a leak tight seal?

- The Mechanical and Molder Rubber plugs create the best seal for pipeline testing. - The standard Multi-Flex plugs may allow some seepage but generally create an acceptable seal, though typically not for pipeline testing. - The MultiFlex plugs may be customized at extra cost with an enhanced seal for testing that includes sealing any longitudinal and circumferential sew seams. - Pipeline conditions such as contamination and corrosion may also influence the seal. - A leak tight sealed best achieved with a double block and bleed plug or multiple plugs with a bleed tap between them.

Can you insert the plug through a hot tap?

Our 128 and 129 PeteStopTM Inflatable Line Stops are designed to be inserted through a hot tap and can provide for most requirements.

Do you sell pipe/piping?

No. We do not.

Do you come and install the plugs?

No, we can train you or your contractor to use our equipment. Contractors on this link are also available to install our equipment - click here to view.

What type of plugs are there?

Typically, we categorize them by Inflatable or Mechanical. We have plugs for most size, pressure, and temperature requirements.

What is the plug shipment lead time?

Many items are in stock for same day shipment. Standard items out of stock generally in 2 - 3 days. Items built for a specific project are manufactured often can be shipped in 2 - 3 weeks. Expediting is usually available upon request

Is the T & P Plug Kit CE Certified?

Per the vendor, yes, it is certified

Where are you located?

We are just north of Milwaukee at 421 Wheeler St. Fredonia, WI 53021

Are your plugs made in the USA?

All Petersen manufactured items are produced in the USA. Some items sourced from others may be manufactured in a country listed in the specifications.